The MPLS-OPS Archive[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index][Thread Index][Author Index][Subject Index] Re: Ethernet over MPLS problem !!!!
Hi Santaqo
Thanks for responding
Platform that we are using is:
PE1 -Cisco7500
PE2- Cisco 7500
IOS that we are using is as follows:
PE1- Version 12.0(25)S1
PE2- Version 12.0(25)S1
As of now we are not using CE1 & CE2 our connectivity is as follows:
You can eliminate CE1 and CE2 from the diagram above.
We have created Vlans on both the switches and and connected the PC at both
ends to the switches.TH switch that we are using at both ends is 2900
series.
Regards
Kartik
----- Original Message -----
From: "Santiago Alvarez" <saalvare@cisco.com>
To: "'kartik'" <kartik.kashyap@estelcom.com>
Cc: <mpls-ops@mplsrc.com>
Sent: Friday, August 29, 2003 6:29 AM
Subject: RE: [MPLS-OPS]: Ethernet over MPLS problem !!!!
What platform? what IOS release? I'd suggest using 12.0(24)S or later where
the xconnect CLI is present. Use 'sh mpl l2 vc det' to troubleshoot your
connection.
Cheers.
SA
--
-----Original Message-----
From: Luciano Salata [mailto:salata-list@ifxnw.com.ar]
Sent: Thursday, August 28, 2003 3:26 PM
To: kartik; mpls-ops@mplsrc.com
Subject: RE: [MPLS-OPS]: Ethernet over MPLS problem !!!!
Hi Rajesh
What platform and IOS code are you running ?
Luciano
-----Mensaje original-----
De: kartik [mailto:kartik.kashyap@estelcom.com]
Enviado el: Miércoles, 27 de Agosto de 2003 11:52 a.m.
Para: mpls-ops@mplsrc.com
Asunto: [MPLS-OPS]: Ethernet over MPLS problem !!!!
Hi
I am trying to simulate ethernet over MPLS , I hav prepared one draft for
that. Is there anybody who can suggest any adivise , as my VC is not coming
UP. I don't know where I am doing the mistake ???
_____
Configuring Draft
for Ethernet over MPLS Testing
Pt. B
CE-1
interface FastEthernet0/1
no ip address
no ip redirects
no ip directed-broadcast
no ip mroute-cache
no keepalive
no cdp enable
interface FastEthernet0/1.12
encapsulation dot1Q 12
ip address 10.0.0.1 255.255.255.0
no ip directed-broadcast
no cdp enable
Pt. A
IP address - 10.0.0.3 255.255.255.0
PE -1
Global Configuration mode-
mpls label protocol ldp
mpls ldp router-id loopback5 force
interface Loopback 5
ip address 202.140.36.65 255.255.255.255
no ip directed-broadcast
interface Serial 1/1/1
ip address 202.131.156.41 255.255.255.252
no ip directed-broadcast
mpls ip
no cdp enable
interface FastEthernet1/0/0
no ip address
no ip redirects
no ip directed-broadcast
no ip mroute-cache
no keepalive
no cdp enable
mpls ip
interface FastEthernet1/0/0.1
encapsulation dot1Q 12
no ip directed-broadcast
mpls l2transport route 202.140.40.65 125
no cdp enable
PE-2
Global Configuration mode-
mpls label protocol ldp
mpls ldp router-id loopback4 force
interface Loopback 4
ip address 202.140.40.65 255.255.255.255
no ip directed-broadcast
interface Serial 1/0/6
ip address 202.131.156.42 255.255.255.252
no ip directed-broadcast
mpls ip
no cdp enable
interface FastEthernet4/0/0
no ip address
no ip redirects
no ip directed-broadcast
no ip mroute-cache
no keepalive
no cdp enable
mpls ip
interface FastEthernet4/0/0.1
encapsulation dot1Q 12
no ip directed-broadcast
mpls l2transport route 202.140.36.65 125
no cdp enable
CE-1
interface FastEthernet0/1
no ip address
no ip redirects
no ip directed-broadcast
no ip mroute-cache
no keepalive
no cdp enable
interface FastEthernet0/1.12
encapsulation dot1Q 12
ip address 10.0.0.2 255.255.255.0
no ip directed-broadcast
no cdp enable
Pt. B
IP address - 10.0.0.4 255.255.255.0
Commands to run during Testing-
1. mpls l2transport route - Enable the local and remote PE router to
establish a virtual circuit.
2. mpls label protocol ldp - Specify the Label Distribution Protocol.
3. mpls ip - enabling dynamic MPLS labeling
Command for verification / Troubleshooting-
1. show mpls ldp discovery - To make sure the PE router endpoints have
discovered each other.
2. show mpls l2transport vc - To check that a VC has been established
between the PE routers and that the VC is operational.
3. show mpls ldp neighbors - To make sure the label distribution
session has been established.
4. show mpls forwarding-table - To make sure the label forwarding table
is built correctly.
The End.
regards
Rajesh Chauhan
-------
The MPLS-OPS Mailing List
Subscribe/Unsubscribe: http://www.mplsrc.com/mplsops.shtml
Archive: http://www.mplsrc.com/mpls-ops_archive.shtml
|
|