The MPLS-OPS Archive

["Martin, Christian" <cmartin@gnilink.net>]

Have you enabled your link-state IGP to advertise TE extensions?

router isis
 metric-style wide
 mpls traffic-eng level-2 (and/or level-1)

./chris

> -----Original Message-----
> From: Rajeev Manur [mailto:rmanur@force10networks.com]
> Sent: Saturday, April 21, 2001 5:22 PM
> To: mpls-ops@mplsrc.com
> Subject: Question on enabling RSVP-TE signalling on GSR
> 
> 
> Here is the test setup :
> 
> GSR is the head-end of an explicit LSP. One of the interfaces 
> of GSR is
> configured with 21.21.21.3/24 as the ip addr. I am seeding 
> the cfg below. I
> have also truned all the debug messages. I don't see GSR 
> initiating RSVP
> signalling ? I would appreciate if any one can help me figure out the
> problem in my cfg..
> 
> with regards,
> Rajeev
> 
> global config dump :
> ==============
> !
> ip subnet-zero
> ip ftp username anvltest
> ip ftp password 7 03025419050A701C
> no ip domain-lookup
> ip host linuxx 172.16.1.239
> ip host linux 25 172.16.1.51
> ip name-server 198.6.1.1
> clns routing
> mpls traffic-eng tunnels
> !
> 
> Tunnel configuration :
> ===============
> 
> !
> interface Tunnel1
>  description First tunnel to pass through the F10-box
>  ip unnumbered Loopback11
>  no ip directed-broadcast
>  tunnel destination 21.21.21.1   # this is the ip addr of 
> connected peer.
>  tunnel mode mpls traffic-eng
>  tunnel mpls traffic-eng priority 1 1
>  tunnel mpls traffic-eng bandwidth 100
>  tunnel mpls traffic-eng path-option 1 explicit identifier 1
> !
> 
> 
> physical interface configuration dump :
> ===========================
> !
> interface FastEthernet0/4
>  ip address 21.21.21.3 255.255.255.0
>  no ip directed-broadcast
>  no ip mroute-cache
>  mpls traffic-eng tunnels
>  ip rsvp bandwidth 1000 1000
> !
> 
> path configuration :
> show ip explicit-paths identifier 1
> PATH 1 (strict source route, path complete, generation 14)
>     1: next-address 21.21.21.3
> 
> 
> 120008-1#show mpls traffic-eng tunnels Tunnel 1 
> 
> Name: First tunnel to pass through the... (Tunnel1) 
> Destination: 21.21.21.1
>   Status:
>     Admin: up         Oper: down   Path: not valid   Signalling: Down
>     path option 1, type explicit 1
> 
>   Config Paramters:
>     Bandwidth:  100       Priority: 1  1   Affinity: 0x0/0xFFFF
>     AutoRoute:  disabled  LockDown: disabled
> 
> 
> 
> 
> 
> -------
> The MPLS-OPS Mailing List
> Subscribe/Unsubscribe:  http://www.mplsrc.com/mplsops.shtml
> Archive: http://www.mplsrc.com/mpls-ops_archive.shtml
> 

-------
The MPLS-OPS Mailing List
Subscribe/Unsubscribe:  http://www.mplsrc.com/mplsops.shtml
Archive: http://www.mplsrc.com/mpls-ops_archive.shtml