The MPLS-OPS Archive

Cell Relay Retreat>MPLS-OPS Archive>month:2005-May> msg00004



[Date Prev][Date Next][Thread Prev][Thread Next]  
  [Date Index][Thread Index][Author Index][Subject Index]

RE: Configure Ethernet over MPLS with Different Customers using the s ame VLAN

  • From: Gary Rose <grose@wams.com>
  • Date: Mon, 9 May 2005 21:53:38 -0700
  • Cc: David Turner <dturner@wams.com>
  • Resent-Date: Tue, 10 May 2005 01:14:17 -0400
  • X-Scanned-By: MIMEDefang 2.45

Hi Rotem,

 

Thanks for the response.

 

Below is our current IOS version and list of modules.

 

IOS 12..2.17D.sx6

 

 

sh mod

Mod Ports Card Type                              Model            

 --- ----- -------------------------------------- ------------------ -----------

  3   48  SFM-capable 48-port 10/100 Mbps RJ45  

  7    2  Supervisor Engine 720 (Active)         WS-SUP720-3BXL    

  8    2  Supervisor Engine 720 (Cold)           WS-SUP720-3BXL    

  9    4  CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE      

 10   16  SFM-capable 16 port 1000mb GBIC        WS-X6516A-GBIC    

 11    4  CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE     

 

Mod Sub-Module                  Model             

--- --------------------------- ------------------ ------------ ------- -------

  7 Policy Feature Card 3       WS-F6K-PFC3BXL    

  7 MSFC3 Daughterboard         WS-SUP720         

8 Policy Feature Card 3       WS-F6K-PFC3BXL    

  8 MSFC3 Daughterboard         WS-SUP720         

  9 Distributed Forwarding Card WS-F6700-DFC3A    

 11 Distributed Forwarding Card WS-F6700-DFC3BXL    

 

 

From: Salomonovitch, Rotem [mailto:rsalomon@uecomm.com.au]
Sent: Monday, May 09, 2005 10:46 PM
To: Gary Rose; Gary Rose; mpls-ops@mplsrc.com
Subject: RE: [MPLS-OPS]: Configure Ethernet over MPLS with Different Customers using the s ame VLAN

 

which sup and PFC or you using on the 6500?

 

From: Gary Rose [mailto:grose@wams.com]
Sent: Tue 5/10/2005 7:43 AM
To: Gary Rose; mpls-ops@mplsrc.com
Subject: RE: [MPLS-OPS]: Configure Ethernet over MPLS with Different Customers using the s ame VLAN

One more clarification, the access ports need to be 802.1q trunk ports.

 

Thanks again.

 

-Gary

From: Gary Rose [mailto:grose@wams.com]
Sent: Monday, May 09, 2005 4:00 PM
To: mpls-ops@mplsrc.com
Subject: [MPLS-OPS]: Configure Ethernet over MPLS with Different Customers using the s ame VLAN

 

Hello Folks,

 

We are implementing a Metro Ethernet network using Cisco 6500 series MPLS switches with the core connected with 10GigE cards. This is a service provider network configured for EoMPLS (Martini Draft) and will have some customers using the same access VLANs.

With a Layer 2 access configuration, what is the best configuration to accomplish this? QinQ? We have no problem using unique VLANs on the PE side but need to ensure that customer access VLANs can overlap each other on the same PE switch.

Any input is much appreciated.

 

Thanks.

 

-Gary

 

 

 

 

 

This message and its attachments may contain legally privileged or confidential information. It is for the intended addressee(s) only.

If you are not the intended recipient you must not disclose or use the information contained in it. If you have received this email in error please notify us immediately by return email and delete the document.

Any views expressed in this message are those of the individual sender, except where the sender specifies and with authority, states them to be the views of the Company.

Uecomm accepts no liability for any damage caused by this email or its attachments due to viruses, interference, interception, corruption or unauthorised access.